24 volt 600w triac & 0 10v dimmable constant voltage outdoor led driver light power supply
Smartspower new 600W 5 in 1 dimmable led power supply constant voltage working mode, built-in active PFC function. Built-in fine-tuning voltage function knob. Suitable for outdoor dimming led lighting project installation.
Specification
| Model | SMT-24600-VTD-J | SMT-36600-VTD-J | SMT-48600-VTD-J | |
| Certificate | CE / ROHS / Reach | |||
| Output | DC Voltage | 24V | 36V | 48V |
| (24V-25.5V adjust by knob) | (36V-38V adjust by knob) | (48V-50V adjust by knob) | ||
| Rated current | 25A | 16.67A | 12.5A | |
| Rated power | 600W | |||
| Voltage Tolerance | ±0.5% | |||
| Voltage Regulation | ≤0.5% | |||
| Load Regulation | ≤1% | |||
| Input | Voltage Range | 110-277VAC | ||
| Frequency Range | 47 - 63Hz | |||
| Power Factor@ full load | ≥0.95 | |||
| THD(Typ.) @ full load | ≤10%@120VAC | |||
| Efficiency @ full load |
90.5%@120VAC 93.45%@277VAC |
90.5%@120VAC 93.45%@277VAC |
90.5%@120VAC 93.45%@277VAC |
|
| AC Current (Max.) | 6.0A | |||
| Inrush Current (Typ.) | 52A, 810us@50%Ipeak110VAC 76A, 148us@50%Ipeak277VAC | |||
| No-load power | <8W | |||
| Standby power | <0.5W | |||
| Leakage current | <0.5mA | |||
| Protection | Short Circuit | Hiccup mode, recovers automatically after fault condition is removed | ||
| Over Load | ≤120% Hiccup mode, recovers automatically after fault condition is removed | |||
| Over temperature | Shell surface temp.100℃±10℃ shut down o/p voltage, automatically recover after cooling | |||
| Environment | Working TEMP. | -40~+60℃ (see below derating curve) | ||
| Working Humidity | 20 - 95%RH non-condensing | |||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | |||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | |||
| Vibration | 10~500Hz, 5G 12min./1 cycle, period for 72min. each along X,Y,Z axes | |||
| Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13(US) | ||
| Withstand voltage | I/P-O/P:1.8KVAC I/P-FG:1.8KVAC O/P-FG:1.8KVAC (US) | |||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | |||
| EMC Emission | FCC 47 CFR Part 15, Subpart B; ANSI C63.4a-2017 (US) | |||
| Others | Net Weight | Kg | ||
| Dimension | 280*140.2*50.2mm(L*W*H) | |||
| Packing | /pcs /CTN | |||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | |||
| 2. Tolerance: includes set up tolerance and load regulation . | ||||
|
|
 |
 |
 |
Mechanical Specification
1. Input UL1015 0.824mm²cable 3*18AWG, Black and White to be connected to AC (L) and (N), Green to be connected to (G).
2. Output UL1015 0.824mm² cable 2*18AWG, Red (+) to LED Positive side (+), Black (-) to LED Negative side (-).
3. Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
Dimming Operation
Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;
Using one dimming ---TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection a phase /Triac dimmer or lighting system.
2. Working with Forward phase, MLV and Reverse phase, ELV, TRIAC dimmers or light system.
3. Min. loading is about 10%
4. Please try to use dimmers with power at least 2 times as the output power of the driver.
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
Ultra-thin size 30W constant voltage LED driver Plastic housing design, waterproof grade ip20. Good heat dissipation. Suitable for indoor lighting project installation. With 7 years warranty
Model: SMT-012-030VTDSP Input Voltage: 100-277vac
Dimming Mode: 5 IN 1 dimmable
|
