CE ROHS listed 240 volt led power supply 40w for led tape
The led power supply 40w IP20 by Smarts can be used both internally project. This constant current power supply is available in 38~50vdc, 700ma project.
Prooduct details
Specification Sheet
Model |
SMT-50-0700CTH |
SMT-45-0900CTH |
SMT-40-1050CTH |
SMT-28-1400CTH |
|
Output |
DC Current |
700mA |
900mA |
1050mA |
1400mA |
Current Accuracy |
±5% |
||||
Voltage Range |
38-50V |
33-45V |
28-40V |
16-28V |
|
Rated power |
40W |
40W |
40W |
40W |
|
Input |
Voltage Range |
180~250VAC |
|||
Frequency Range |
47~63HZ |
||||
Power Factor (Typ.) |
PF≧0.93/110V ; PF≧0.95/220V ; PF≧0.94/250V |
||||
Full Load Efficiency(Typ.) |
>85% |
>85% |
>85% |
>85% |
|
AC Current(Typ.) |
0.14A/110VAC 0.12 A/220VAC 0.01A/250VAC |
||||
Leakage current |
<0.27mA/110VAC; ﹤0.25mA/220VAC |
||||
Protection |
Short Circui |
Hiccup mode, recovers automatically after fault condition is removed. |
|||
Over voltage |
≦270VAC |
||||
Environment |
Working TEMP. |
-40~+60℃ |
|||
Working Humidity |
20~90%RH,non-condensing |
||||
Storage TEM.,Humidity |
-40~+80℃,10~95%RH |
||||
TEMP.coefficient |
±0.03%/℃(0~50℃) |
||||
Vibration |
10~500Hz,2G 10min./1 cycle,period for 60min. each along X,Y,Z axes |
||||
Safety&EMC |
Safety standards |
EN-60950-1, EN-61347-1-2 |
|||
Withstand voltage |
I/P-O/P:3.75KVAC |
||||
Isolation resistance |
I/P-O/P:100MΩ/500VDC/25℃/70%RH |
||||
EMC EMISSION |
Compliance toEN55015,EN61000-3-2 (≧50%load) |
||||
EMC IMMUNITY |
Compliance to EN55015,EN61000-4-2,3,4,5,6,8,11,A light industry level (surge4KV) |
||||
Others |
Weight |
0.34Kg/pcs |
|||
Size |
110*45*26mm (L*W*H) |
||||
packing |
290*275*190mm |
||||
Notes |
1. All parameters NOT specially mentioned are measured at 110V/230VAC input , rated load and 25℃of ambient temperature. 2. Ripple& noise are measured at 20MHz of bandwidth by using a 12”twisted pair-wire terminated with a 0.1uf &47uf parallel capacitor. 3. Tolerance:includes set us tolerance,line regulation and load regulation . |
Simple Connection Diagram
FAQ
1.What is the difference between the 20w/45w UL and 24w/48w ETL model?
Answer:
-- when you install a 20w/45w UL led driver in your led light you should consider abbot min. 55% load limtation. If it less than 55%, the led light will have flick problem. But the 20w/45w ETL model is no load limitation. You can load it in the led light 1-48w.
-- the height of 24w(20mm)/48w(24mm) is lower than 20w(28mm)/45w(34mm).
2.If the connection load less than 55% for the load limitation led driver, what will happen?
Answer: If you take our 1.0V triac dimmable led drivers, the led light will have flick problem
3. What is the shipping way do you have?
Answer:
--By air, by sea.