Dali ultra slim led driver 12v 100w aluminum case for outdoor using
Dali led driver 12v 100w dimmable with output short circuit protection, over power protection, overheating protection. Metal housing and high power factor allow the driver to operate in maximum reliability. Brilliant Lighting LED strip STRP5050-65WW can be compatible in principle.
Specification：
|
model |
SMT-012-100VMSWH |
SMT-024-096VMSWH |
|
|
Output |
DC Voltage |
12VDC |
24VDC |
|
Voltage Tolerance |
±0.5V |
±0.5V |
|
|
Rated current |
8.33Amp |
4.0Amp |
|
|
Rated power |
100W |
96W |
|
|
Voltage Regulation |
±0.5% |
||
|
Load Regulation |
±2% ±1% |
||
|
Input |
Voltage Range |
100-277VAC |
|
|
Frequency Range |
47～63HZ |
||
|
Power Factor(Typ.)@ full load |
0.98@120VAC |
0.98@120VAC |
|
|
Efficiency(Typ.)@ full load（Typ.） |
>88% |
>88% |
|
|
AC Current(Max.) |
1.2A@100VAC |
||
|
THD(Typ. ) @ full load |
10%@120VAC |
10%@120VAC |
|
|
Inrush Current（Typ.） |
4.1A (twidth=220us) @120VAC ; 35.2A (twidth=164us) @230VAC ; 12.8A (twidth=960us) @277VAC ; |
||
|
Leakage current |
<0.5mA |
||
|
Protection |
Short Circuit |
shut down o/p voltage, re-power on to recover afterfault condition removed |
|
|
Over Load |
≤120% Hiccup mode ,recovers automatically after fault condition is removed or shut down o/p voltage, re-power on to recover afterfault condition removed |
||
|
Protection Class |
I |
||
|
Over temperature |
100℃±10℃ shut down o/p voltage,automatically recover after cooling
|
||
|
Environment |
Working TEMP. |
-40~+60℃ (see below derating curve) |
|
|
Working Humidity |
20～95%RH,non-condensing |
||
|
Storage TEM.,Humidity |
-40～+80℃，10～95%RH |
||
|
TEMP.coefficient |
±0.03%/℃（0～50℃） |
||
|
Vibration |
10～500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes |
||
|
Safety&EMC |
Safety standards |
EN61347-1 EN61347-2-13 (EU) and UL8750 (US) |
|
|
Withstand voltage |
I/P-O/P:3.75KVAC (EU) and I/P-O/P:1.88KVAC (US) |
||
|
Isolation resistance |
I/P-O/P：100M Ohms/500VDC/25℃/70%RH |
||
|
EMC EMISSION |
Compliance to EN55015, EN61000-3-2 (≥60%load) (EU) andFCC Part 15 (US) |
||
|
EMC IMMUNITY |
Compliance to EN61000-4-2,3,4,5,6,11, EN61547, light industry |
||
|
Others |
Net Weight |
0.53Kg |
|
|
Size |
330*32*23mm(L*W*H) |
||
|
packing |
360*270*175mm/30PCS/CTN G.W.:16.9KG/CTN |
||
|
Notes |
1. All parameters NOT specially mentioned are measured at230VAC input , rated load and 25℃of ambient temperature. 2. Tolerance: includes set up tolerance, line regulation and load regulation . 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. |
||
 |
 |
 |
 |
■ Mechanical Specification
Unite: mm Tolerance:P 0.5-2mm
Ø Input Rubber cable H05RN-F 3*1.0mm², the green/yellow cable connect with (FG) ,Brown with AC (L),Blue with AC(N)
Ø Output rubber cable H05RN-F 2*1.0mm², Red is output ( V+) Positive, Black is output (V-) negative. Connected to LED Lights
■ Dimming wiring
Ø Dimming Rubber cable H05RN-F 2*0.75mm², Blue DA/N and White DA/L (No polar) connected to the DALI BUS when use DALI function .
Note: Blue (N) is connected to AC (N) while white (L) is connected to Push dim switch dimmer( L) when use Push function.
Ø Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
■ Derating Curve
Ø To extend their life, please refer to the Derating Curve and derate according to the temperature.
■ Dimming Operation
Note: For DALI Dimming Wiring Diagram 3, please noted that only one DALI power is need in the DALI bus, so no extra DALI power is needed if the Master or Dimmer already includes the DALI Power.
■ Instruction:
Ø This driver should be installed by qualified and professional person;
Ø Please make sure the driver is installed with adequate ventilation around it to allow for heat dissipation.
Ø Ensure that wiring is correct before test in order to avoid light and power supply damage;
Ø If the dimmable LED drivers do not work normally, pl. don’t maintain privately, but contact us: sales9@smartselectronics.com Or take a phonecall: 0086-18016688251
Official website: www.smarts-electronics.com & www.swinpower.com
Compatible Dimmer Type
This waterproof exterior led driver 12v with aluminum shell is super slim, which can be installed anywhere you like. The size is 330*32*23mm(L*W*H). With CE/ROHS certificaiton. Can be work with Nilight led light bar 600537011472.
|
Related Products
|
|
12v 100w ultra slim led transformer has the same specification with SMT-012-100VMSWH. The maxium output voltage is 100w. The only difference is this driver is for indoor using.
Mode：SMT-012-100VMSPH intput voltage：100~277V AC Dimming mode:DALI dimming Efficiency > 88% Certification: CE ROHS
|
