pwm output constant voltage triac dimmable led strip light power supply driver for led strip light
New upgraded triac dimmable led driver 24v 96W integrated with junction box, fully protected aluminum housing design. Suitable for outdoor dry and wet lighting projects. Complies with global safety lighting regulations. Mainly sold to North America
Specification
| Model | SMT-24096-VT-J | SMT-48096-VT-J | |
| Certificate | UL / FCC / Class 2 / Class P / SELV / CE / RoHs / REACH | ||
| Output | DC Voltage | 24V | 48V |
| Voltage Tolerance | ±2% | ±2% | |
| Voltage Regulation | ≤0.5% | ≤0.5% | |
| Load Regulation | ≤2% | ≤2% | |
| Rated current | 4A | 2A | |
| Rated power | 96W | ||
| Voltage Ripple | 296mv | 176mv | |
| Overshoot voltage | <3%(full load) | <3%(full load) | |
| Fine-tune Voltage | 24-26V | 48-50V | |
| Dimming Mode | The DIP switch in the "ON" position represents the PWM | ||
| (Pulse - Width Modulation) mode, and in the "1" position | |||
| represents the VR (Modulation of DC Voltage) mode. | |||
| Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | |||
| Input | Voltage Range | 100-277VAC | |
| Frequency Range | 47 - 63Hz | ||
| Power Factor (Typ.) @ full load |
>0.98@120VAC >0.97@277VAC |
>0.98@120VAC >0.97@277VAC |
|
| THD(Typ. ) @ full load | ≤15%@full load | ||
| Efficiency(Typ.) @ full load |
≥88%@120VAC ≥91.5%@277VAC |
≥87%@120VAC ≥90.5%@277VAC |
|
| AC Current (Max.) | ≤1.0A @120VAC ≤0.43A@277VAC | ||
| Inrush Current (Typ.) | 51A,208us@50%Ipeak 120VAC 118A,452us@50%Ipeak 277VAC | ||
| Leakage current | <0.5mA | ||
| Protection | Short Circuit | Hiccup or Locking mode, recovers automatically after fault condition is removed | |
| Over Load | >120% Constant current (limited power) mode, recovers automatically after fault condition is removed | ||
| Over temperature | When the ambient temperature exceeds 55℃ ±5℃, the output is turned off | ||
| Environment | Working TEMP. | -40~+40℃ (see below derating curve) | |
| Working Humidity | 20 - 95%RH non-condensing | ||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||
| Vibration | 10 ~ 500Hz, 5G 12 minutes/cycle, X Y Z axis 72 minutes each | ||
| Ambient TEMP. | 40℃ | ||
| Case TEMP. | 75℃ | ||
| Safety & EMC | Safety standards | UL8750 (US) CAN/CSA-C22.2 No.250.13 | |
| Withstand voltage | I/P-O/P:1.88KVAC;I/P-FG:1.5KVAC;O/P-FG:0.5KVAC | ||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | ||
| Surge Immunity Test | AC Power Line:Differential Mode 2KV,Common Mode 4KV | ||
| EMC Immunity | FCC/ICES do not request this test | ||
| EMC Emission | FCC Part15 Subpart B (US) | ||
| Others | Ta&Tc | Ta 40℃ Tc 75℃ | |
| Net Weight | 1.06Kg | ||
| Dimension | 188.0*95.4*42.7mm(L*W*H) | ||
| Packing | 415*265*270mm 20 pcs / CTN | ||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | ||
| 2. Tolerance: includes set up tolerance and load regulation . | |||
|
|
 |
 |
 |
Mechanical Specification
1.Input 1015 0.824mm2 3*18AWG: Black cable (L), White cable (N), Green cable (G).
2.Output 1015 0.824mm2 2*18AWG: Red cable(V+) connect to positive(+), Black cable(V-) connect to negative(-).
3.Please make sure your connect these correctly otherwise your product will not function correctly and could be damaged.
Dimming Operation
TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection
2. phase /Triac dimmer or lighting system.
3. Working with forward phase, MLV and Reverse phase , ELV, TRIAC dimmers.
4. Min. loading is about 10%.
5. Please try to use dimmers with power at least 1.5 times as the output power of the driver.
Related Products
|
Aluminum housing design waterproof grade ip20 triac dimmable 24v 96W led power supply constant voltage working mode.
Model: SMT-012-100VTSP Input Voltage: 100-277vac
Dimming Mode: triac dimmable
|
