100-277vac triac & 0 10v constant voltage led driver Junction Box 60w 12v/24v/36v/48v
Smartspower new 5 in 1 dimmable LED power supply has short circuit / over temperature / overload protection. It has ultra-low load requirements and can work perfectly at 20%-100% load. The dimming range is smooth and flicker-free between 0-100%. It has a 7-year warranty
Specification
| Model | SMT-12060-VTD-P | SMT-24060-VTD-P | SMT-36060-VTD-P | SMT-48060-VTD-P | |
| Certificate | UL / cUL / FCC / Class 2 / Class P / SELV / CE / ROHS/ REACH | ||||
| Output | DC Voltage | 12V | 24V | 36V | 48V |
| Fine-tune voltage range | 12-13.5V | 24-26V | 36-38V | 48-50V | |
| Rated Current | 5A | 2.5A | 1.67A | 1.25A | |
| Current Tolerance | ±0.5V | ||||
| Rated Power | 60W | ||||
| Load Regulation | ≤2% | ≤1% | ≤1% | ≤1% | |
| Voltage Regulation | ≤0.5% | ||||
| Dimming mode selection | PWM & VR two modes for choice ON for PWM mode while 1 for VR mode | ||||
| Power off till three seconds, then power-on for mode switch | |||||
| Input | Voltage Range | 100-277VAC | |||
| Frequency Range | 47 - 63Hz | ||||
| Power Factor @ full load |
≥0.98@120VAC ≥0.95@277VAC |
≥0.98@120VAC ≥0.95@277VAC |
≥0.98@120VAC ≥0.95@277VAC |
≥0.98@120VAC ≥0.95@277VAC |
|
| Efficiency @ full load |
≥82%@120VAC ≥84%@277VAC |
≥82%@120VAC ≥84%@277VAC |
≥82%@120VAC ≥84%@277VAC |
≥83%@120VAC ≥85%@277VAC |
|
| AC Current (Max.) | ≤0.8A | ||||
| THD(Typ.) @full load | ≤20%@ 120VAC ≤20%@ 277VAC | ||||
| Lightning surge | Line to line: 2KV | ||||
| Inrush Current (Typ.) | 16A, 50%Ipeak 232us @120VAC 36A, 50% Ipeak 248us @277VAC | ||||
| Leakage current | ≤0.5mA | ||||
| Protec-tion | Short Circuit | Hiccup or Constant current mode, re-power onto recover after fault condition removed | |||
| Over Load | ≥120% Constant current (limited power) mode, auto-recovery after fault condition removed | ||||
| Over Temperature | Shell surface temp.100℃±10℃shut down o/p voltage and automatically recover after cooling | ||||
| Environ-ment | Working TEMP | -40~+60℃ (see below derating curve) | |||
| Working Humidity | 20 -90%RH non-condensing | ||||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||||
| Vibration | 10~500Hz, 2G 12min./1 cycle, period for 72min. each along X,Y,Z axes | ||||
| Safety & EMC | Safety standards | UL8750 UL1310 (US) | |||
| EMC Emission | EN55015 EN61000-3-2,3(≥50% load) FCC Part 15 Subpart B (US) | ||||
| EMC Immunity | FCC/ICES do not request this test (US) | ||||
| Withstand voltage | I/P-O/P:1.88KVAC (US) | ||||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70%RH | ||||
| Stroboscopic test | IEEE 1789 | ||||
| Others | Net Weight | 0.36Kg | |||
| Dimension | 178*61*24mm(L*W*H) | ||||
| Packing | 290*215*140mm 20pcs /CTN | ||||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input,rated load and 25℃ of ambient temperature. | ||||
| 2. Under low input voltage, derating output is required to ensure a long life. | |||||
|
|
 |
 |
 |
Mechanical Specification
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 9 |
| 13A | 11 | |
| 16A | 14 | |
| 20A | 18 | |
| 25A | 23 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 24 |
| 13A | 32 | |
| 16A | 40 | |
| 20A | 50 | |
| 25A | 62 | |
MCB recommendation：
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 9 |
| 13A | 11 | |
| 16A | 14 | |
| 20A | 18 | |
| 25A | 23 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 24 |
| 13A | 32 | |
| 16A | 40 | |
| 20A | 50 | |
| 25A | 62 | |
Note：
1. The above quantities of the led drivers connected on the Type C is recommended base on the maximum ambient temperature is 50 ℃.
2. The breaker should be selected according to the input rated voltage, input rated current, ambient temperature, and trip characteristic curve.
Dimming Operation
Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;
l Using one dimming ---TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection
a phase /Triac dimmer or lighting system.
2. Working with forward phase /leading edge, MLV and Reverse phase /trailing edge, ELV, TRIAC dimmers or light system.
3. Min. loading is about 20%
4. Please try to use dimmers with power at least 1.5 times as the output power of the driver.
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
60W 5 IN 1 dimmable led power supply is compact, with dimensions of 188*94.5*40mm, easy and quick installation. Universal input voltage range 100-277vac UL certified, in line with global safety lighting regulations. With 7-year warranty
Model: SMT-012-060VTDHV2 Input Voltage: 100-277vac
Dimming Mode: 5 in 1 dimmable
|
