12VAC/24VAC constant voltage triac & 0 10v dimmable 96W led strip power supply for indoor
30W 5 in 1 dimmable led power supply plastic shell design, waterproof grade ip20, suitable for indoor small space lighting project installation, with ultra-low load requirements, can work perfectly under 20%-100% load
Specification
| Model | SMT-12030-VTD-P | SMT-24030-VTD-P | SMT-48030-VTD-P | |
| Certificate | UL / FCC / Class P | |||
| Output | DC Rate Voltage | 12V | 24V | 48V |
| Voltage Tolerance | ±5%Vo | ±2.5%Vo | ±1.25%Vo | |
| Load Regulation | ≤1% | ≤1% | ≤1% | |
| Line Regulation | ≤0.5% | ≤0.5% | ≤0.5% | |
| Rated current | 2.5A | 1.25A | 0.63A | |
| Rated power | 30W | 30W | 30W | |
| Voltage Ripple | 500mVp-p | 400mVp-p | 350mVp-p | |
| Overshoot voltage | <1%(full load),<2%(no load) | |||
| Output volt Adjustment | 12-13V | 24-26V | 48-50V | |
| Output mode selection | The DIP switch in the "ON" position represents the PWM (Pulse - Width Modulation) mode, and in the "1" position represents the VR (Modulation of DC Voltage) mode. | |||
| Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | ||||
| Input | Voltage Range | 100-277VAC | ||
| Frequency Range | 47 - 63Hz | |||
| Power Factor @ full load | >0.98@120VAC >0.95@277VAC | |||
| THD(Typ.) @ full load | <20%@120V <20%@277V | |||
| Efficiency @ full load | >78%@120VAC >80%@277VAC | |||
| AC Current (Max.) | ≤0.4A @120VAC ≤0.16A@277VAC | |||
| Inrush Current (Typ.) | 25A,120us@50%Ipeak 120VAC 60A,136us@50%Ipeak 277VAC | |||
| Leakage current | ≤0.5mA | |||
| Protection | Short Circuit | Hiccup mode, can be automatically restored after abnormal removal | ||
| Over Load | ≤120%,Constant - Current Mode, automatic recovery after exception | |||
| Over temperature | When the ambient temperature exceeds 55℃ ±5℃, the output is turned off | |||
| Environment | Working TEMP. | -40~+40℃ (see below derating curve) | ||
| Working Humidity | 20 - 90%RH non-condensing | |||
| Storage TEM.,Humidity | -40 ~ +80℃,10 - 95% RH non-condensing | |||
| TEMP.coefficient | ±0.03%/℃(0 ~ 50℃) | |||
| Vibration | 10 ~ 500Hz, 2G 12 minutes/cycle, X Y Z axis 72 minutes each | |||
| Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13 | ||
| Withstand voltage | I/P-O/P:1.88KVAC | |||
| Isolation resistance | I/P-O/P:>100MΩ / 500VDC / 25℃ / 70% RH | |||
| Surge Immunity Test | AC Power Line:Differential Mode 2KV | |||
| EMC Immunity | FCC/ICES do not request this test | |||
| EMC Emission | FCC Part15 Subpart B;ANSI C63.4:2017;ICES-005 Issue 5 | |||
| Others | Net Weight | 250g | ||
| Dimension | 155*54*19.7mm(L*W*H) | |||
| Packing | 40 pcs / CTN | |||
| Notes | 1. Unless otherwise specified, all specifications are measured at 120V input, rated load, and 25℃ ambient temperature. | |||
| 2. In the case of low input voltage, derated output should be used to ensure a long service life. | ||||
|
3.default states: ① The output mode is PWM output by default. ② The dimming curve is a gamma2.2 curve. |
||||
| 4. LED driver Meets the harmonic emissions requirements of ANSI C82.77-10. | ||||
|
|
 |
 |
 |
Mechanical Specification
| American wire gauge | |
| CA5 | |
| Input wire | Black(L) White(N) Green(G) (3*18 AWG) |
| Output wire | Red(V+) Black(V-) (2*18 AWG) |
| Dimming terminal | Purple(D+) Pink(D-) (2*18AWG) |
| Function switching wire | Purple and Pink.(2*22 AWG) |
MCB recommendation：
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 18 |
| 13A | 23 | |
| 16A | 29 | |
| 20A | 35 | |
| 25A | 45 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 45 |
| 13A | 58 | |
| 16A | 72 | |
| 20A | 89 | |
| 25A | 112 | |
Note：
1. The above quantities of the led drivers connected on the Type C is recommended base on the maximum ambient temperature is 50 ℃.
2. The breaker should be selected according to the input rated voltage, input rated current, ambient temperature, and trip characteristic curve.
Dimming Operation
Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;
l Using one dimming ---TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection
a phase /Triac dimmer or lighting system.
2. Working with forward phase /leading edge, MLV and Reverse phase /trailing edge, ELV, TRIAC dimmers or light system.
3. Min. loading is about 20%
4. Please try to use dimmers with power at least 1.5 times as the output power of the driver.
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
Plastic housing ip20 triac & 0 10V dimmable constant voltage led power supply 30W. With ultra low load requirement. Able to work perfectly at 20%-100% load. With compact size, it is suitable for indoor led lighting project installation.
Model: SMT-012-030VTD Input Voltage: 100-277vac
Dimming Mode: Non dimmable
|
