triac & 0 10v dimming constant voltage 96W 24V led light strips driver power supply for led lights
Smartspower's new upgraded 5 in 1 dimmable 96W LED power supply has short circuit/over temperature/overload protection functions. Plastic shell design, waterproof grade ip20. Suitable for indoor small space lighting project installation. 7 years warranty
Specification
| Model | SMT-24096-VTD-P | SMT-48096-VTD-P | |
| Certificate | UL / cUL / FCC / Class P / Class 2/SELV/RoHS | ||
| Output | DC Voltage | 24V | 48V |
| Voltage Tolerance | ±4% | ±2% | |
| Voltage Regulation | ≤1% | ≤0.5% | |
| Load Regulation | ≤1% | ≤1% | |
| Rated current | 4A | 2A | |
| Rated power | 96W | ||
| Voltage Ripple | 296mVp-p | 176mVp-p | |
| Overshoot voltage | <3% (full load) <4%(no load) | ||
| Output volt Adjustment | 24-26V | 48-50V | |
| Output mode selection | The DIP switch in the "ON" position represents the PWM (Pulse - Width Modulation) mode, and in the "1" position represents the VR (Modulation of DC Voltage) mode. | ||
| Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | |||
| Input | Voltage Range | 100-277VAC | |
| Frequency Range | 47 - 63Hz | ||
| Power Factor (Typ.) @ full load |
>0.98@120VAC >0.96@277VAC |
>0.98@120VAC >0.96@277VAC |
|
| THD(Typ. ) @ full load | <15%@120V <15%@277V | ||
| Efficiency(Typ.) @ full load |
≥88.0%@120VAC ≥91.5%@277VAC |
≥87.2%@120VAC ≥90.6%@277VAC |
|
| AC Current (Max.) | ≤1.0A @120VAC ≤0.43A@277VAC | ||
| Standby power | ≤0.5W | ||
| Inrush Current (Typ.) | 51A@50%Ipeak 208us @120VAC,118A@50%Ipeak 452us @277VAC. | ||
| Leakage current | <0.5mA | ||
| Protection | Short Circuit | Hiccup mode, can be automatically restored after abnormal removal | |
| Over Load | ≥120%,Constant - Current Mode, automatic recovery after exception | ||
| Over temperature | When the ambient temperature exceeds 55℃ ±5℃, the output is turned off | ||
| Environment | Working TEMP. | -40~+40℃ (see below derating curve) | |
| Working Humidity | 20 - 90%RH non-condensing | ||
| Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||
| TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||
| Vibration | 10 ~ 500Hz, 2G 12 minutes/cycle, X Y Z axis 72 minutes each | ||
| Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13 | |
| Withstand voltage | I/P-O/P:1.88KVAC | ||
| Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | ||
| Surge Immunity Test | AC Power Line:Differential Mode 2KV | ||
| EMC Immunity | FCC/ICES do not request this test | ||
| EMC Emission | FCC Part15 Subpart B;ANSI C63.4:2017;ICES-005 Issue 5 | ||
| Others | Net Weight | 0.36KG | |
| Dimension | 178*61.1*24mm(L*W*H) | ||
| Packing | 290*215*140mm 20 pcs / CTN | ||
| Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | ||
| 2. Tolerance: includes set up tolerance and load regulation . | |||
| 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. | |||
|
4. Default states: The output mode is PWM output by default. The dimming curve is a gamma2.2 curve. |
|||
| 5. Regarding LED driver load types where the driver meets the harmonic emissions requirements of ANSI C82.77-10. | |||
|
|
 |
 |
 |
Mechanical Specification
| Notes | American wire gauge |
| Enclosure model | SD8 |
| Input wire | DG128-3P |
| Output wire | DG128-2P |
| Dimming wire | DG128-2P |
Warm tips:
1. Recommended Max. Carrying Current (A) = wire diameter(mm²) x 10A/mm ²
For example: 1mm ² output cable, Recommended Max. Carrying Current (A) = 1mm ² x 10A/mm ²=10A
2. Any other requests for cable, we can customized.Any other requests for cable, we can customized
MCB recommendation：
| When the input voltage is 120Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 6 |
| 13A | 7 | |
| 16A | 9 | |
| 20A | 12 | |
| 25A | 15 | |
| When the input voltage is 277Vac,the number of LED Driver matched by circuit breakers is as follows: | ||
| MCB Type | Level | The number of LED Driver |
| C type | 10A | 14 |
| 13A | 18 | |
| 16A | 22 | |
| 20A | 28 | |
| 25A | 30 | |
Note：
1. The above quantities of the led drivers connected on the Type C is recommended base on the maximum ambient temperature is 50 ℃.
2. The breaker should be selected according to the input rated voltage, input rated current, ambient temperature, and trip characteristic curve.
Dimming Operation
Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;
l Using one dimming ---TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection
a phase /Triac dimmer or lighting system.
2. Working with forward phase /leading edge, MLV and Reverse phase /trailing edge, ELV, TRIAC dimmers or light system.
3. Min. loading is about 20%
4. Please try to use dimmers with power at least 1.5 times as the output power of the driver.
Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming
Related Products
|
This triac & 0 10v dimmable 96W 24V led power supply is integrated with the junction box and has a metal housing design. It is suitable for indoor smart dimming lighting project installation. It has a 7-year warranty
Model: SMT-024-096VTDHV2 Input Voltage: 100-277vac
Dimming Mode: 5 in 1 dimmable
|
