waterproof IP67 24v dimmable 150W constant voltage led power supply led strip light for outdoor
100-277VAC universal input voltage range. 5 in 1 dimmable constant voltage LED driver. Waterproof grade IP67, aluminum housing design, suitable for outdoor wet space lighting project installation. With 7 years warranty
Specification
Model | SMT-12150-VTD-A | SMT-24150-VTD-A | SMT-36150-VTD-A | SMT-48150-VTD-A | |
Certificate | UL\FCC\SELV\Class P\TYPE HL\ICES | ||||
Output | DC Voltage | 12V | 24V | 36V | 48V |
Voltage Tolerance | ±4% | ±3% | ±3% | ±2% | |
Voltage Regulation | ≤0.5% | ≤0.5% | ≤0.5% | ≤0.5% | |
Load Regulation | ≤3% | ≤2% | ≤1% | ≤1% | |
Rated current | 12.5A | 6.25A | 4.17A | 3.125 | |
Rated power | 150W | ||||
Voltage Ripple | 250mVp-p | 250mVp-p | 250mVp-p | 250mVp-p | |
Overshoot voltage | <1%(full load),<2%(no load) | ||||
Output volt Adjustment | 12-13V | 24-26V | 36-38V | 48-50V | |
Output mode selection | When the black wire and the White\Gray wire at the output terminal are short-circuited, it indicates the Pulse-Width Modulation (PWM) mode. When they are disconnected, it indicates the Voltage Regulation (VR) mode of direct current voltage modulation. | ||||
Switching the output mode requires the power to be cut off for 3 seconds and then powered on again for the mode switching to take effect. | |||||
Input | Voltage Range | 120-277VAC | |||
Frequency Range | 47 - 63Hz | ||||
Power Factor (Typ.) |
>0.98@120VAC >0.97@277VAC |
>0.98@120VAC >0.97@277VAC |
>0.98@120VAC >0.97@277VAC |
>0.98@120VAC >0.97@277VAC |
|
THD(Typ. ) @ full load | <15%@120V <15%@277V | ||||
Efficiency(Typ.) @ full load |
≥86.0%@120VAC ≥89.5%@277VAC |
≥89.0%@120VAC ≥92%@277VAC |
≥89.0%@120VAC ≥92.5%@277VAC |
≥89.0%@120VAC ≥91.5%@277VAC |
|
AC Current (Max.) | ≤1.7A @120VAC ≤0.68A@277VAC | ||||
Standby power | ≤0.5W | ||||
Inrush Current (Typ.) | 68A 208us@50%Ipeak 120VAC 100A 452us@50%Ipeak 277VAC | ||||
Leakage current | <0.5mA | ||||
Protection | Short Circuit | Hiccup mode, can be automatically restored after abnormal removal | |||
Over Load | ≤120%,Constant - Current Mode, automatic recovery after exception | ||||
Over temperature | When the shell temperature reaches 100℃±10℃, the power supply shut down the output, the temperature drop can be automatically restored | ||||
Environment | Working TEMP. | -40~+60℃ (see below derating curve) | |||
Working Humidity | 20 - 90%RH non-condensing | ||||
Storage TEM.,Humidity | -40 - +80℃,10 - 95% RH non-condensing | ||||
TEMP.coefficient | ±0.03%/℃(0 - 50℃) | ||||
Vibration | 10 ~ 500Hz, 5G 12 minutes/cycle, X Y Z axis 72 minutes each | ||||
Safety & EMC | Safety standards | UL8750 CAN/CSA-C22.2 No.250.13 | |||
Withstand voltage | I/P-O/P:1.88KVac;I/P-FG::1.88KVac;O/P-FG:0.5KVac | ||||
Isolation resistance | I/P-O/P:100MΩ / 500VDC / 25℃ / 70% RH | ||||
Surge Immunity Test | AC Power Line:Differential Mode 2KV,Common Mode 4KV | ||||
EMC Immunity | FCC/ICES do not request this test | ||||
EMC Emission | FCC Part15 Subpart B | ||||
Others | Net Weight | 0.8kg | |||
Dimension | 200*78*25.1mm(L*W*H) | ||||
Packing | 495*245*200mm 20 pcs / CTN | ||||
Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input, rated load and 25℃of ambient temperature. | ||||
2. Tolerance: includes set up tolerance and load regulation . | |||||
3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. | |||||
4. Default states: The output mode is PWM output by default. The dimming curve is a gamma2.2 curve. |
|||||
5. Regarding LED driver load types where the driver meets the harmonic emissions requirements of ANSI C82.77-10. |
Mechanical Specification
American wire gauge | |
DT61 | |
12V & 24V & 36V & 48V Version Input wire | SJOW rubber wire\Black(L),White(N),Green(G)(3*0.824mm2) |
Output wire | SJOW rubber wire\16 AWG\Red(+) and Black(-) (2*1.31mm2)(12V & 24V Version) |
SJOW rubber wire\18 AWG\Red(+) and Black(-) (2*0.824mm2)(36V & 48V Version) | |
12V & 24V & 36V & 48V Version function switching wire | SJOW rubber wire\18 AWG\Black and White\Gray (2*0.824mm2) |
12V & 24V & 36V & 48V Version Dimming wire | SJOW rubber wire\18 AWG\Purple(D+) and Pink(D-) (2*0.824mm2) |
Warm tips:
1. Recommended Max. Carrying Current (A) = wire diameter(mm²) x 10A/mm ²
For example: 1mm ² output cable, Recommended Max. Carrying Current (A) = 1mm ² x 10A/mm ²=10A
2. Any other requests for cable, we can customized.
Dimming Operation
Using two ways of dimming at the same time, you must be assured that LED lighting is up to the max. Brightness then you could operate with the other dimming;
l Using one dimming ---TRIAC/Phase cut dimming
1. The Pulse-Width Modulation (PWM) of output voltage can be adjusted through input terminal of the AC phase line(L) by connection
a phase /Triac dimmer or lighting system.
2. Working with forward phase /leading edge, MLV and Reverse phase /trailing edge, ELV, TRIAC dimmers or light system.
3. Min. loading is about 20%
4. Please try to use dimmers with power at least 1.5 times as the output power of the driver.

Using one dimming ---0-10/ 1-10V/ 10V PWM/ Potentiometer dimming

Related Products
Aluminum housing triac & 0 10v dimmable led driver good heat dissipation, waterproof grade ip67. With short circuit / over temperature / overload protection function. Suitable for outdoor humid space lighting project installation. With 7 years warranty
Model: SMT-012-150VTD Input Voltage: 100-277vac
Dimming Mode: 5 in 1 dimmable
|