277v ac dc 12v 150w led driver 0-10V dimmable power supply
SMT-012-150VDH is UL approved 150w led driver. It is driver and junction box integrated with high PF>0.95, high Efficiency>88%, 7 years warranty.
Features of led power supply
Output constant voltage type
·Range 100-305VAC , Typical: 100-277VAC
·Built-in PFC function PF>0.90
·Efficiency > 88%
·Protections:short circuit/over current/over voltage/over temperature
·Cooling by free air convection
·IP20 design for indoor or outdoor installations .
·Dimming function:0-10V/ 1-10V/ 10VPWM signal or resistance .
·Suitable for LED lighting and moving sign applications
·Compliance to worldwide safety regulations for lighting
·Suitable for dry/damp locations
·7 years warranty
Specification of led power supply
Model
SMT-012-150VDH
SMT-024-150VDH
Output
DC Voltage
12V
24V
Voltage Tolerance
±0.5V
Voltage Tolerance
±0.5V
Voltage Regulation
±0.5%
Rated current
12.5A
6.25A
Rated power
150W
150W
Input
Voltage Range
100-277VAC
Frequency Range
47~63HZ
Power Factor ( Typ.)
PF≧0.98/110V , PF≧0.95/277V
PF≧0.98/110V , PF≧0.95/277V
Full Load
Efficiency(Typ.)
>87%
>88%
AC Current(Typ.)
1.8A@110VAC
1.32A
Inrush Current (Typ.)
15A, 50%, 1.4ms
Leakage current
<0.50mA
Protection
Short Circuit
shut down o/p voltage, re-power on to recover after fault condition is removed
Over load
≤120% constant current limiting, auto-recovery
TEMP .coefficient
±0.03%/℃(0~50℃)
Vibration
10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes
Over Current
≤1.4*I out
Environment
Working TEMP.
-40~+60℃
Working Humidity
20~90%RH,non-condensing
Storage TEM.,Humidity
-40~+80℃,10~95%RH
TEMP.coefficient
±0.03%/℃(0~50℃)
Vibration
10~500Hz 2G 10min./1 cycle,period for 60min.each along X,Y,Z
axes
Safety&EMC
Safety standards
EN61347-1 EN61347-2-13
Withstand voltage
I/P-O/P:3.75KVAC
Isolation resistance
I/P-O/P:100MΩ/500VDC/25℃/70%RH
EMC EMISSION
Compliance to EN55015,EN61000-3-2 (≧50%load)
EMC IMMUNITY
EN61000-4-2,3,4,5,6,11(Surge about 4KV)
Others
Weight
1.8Kg
Size
260*103*46mm (L*W*H)
packing
440*295*145mm ,10PCS/CTN
Notes
1. All parameters NOT specially mentioned are measured at 110V/277VAC input , rated load and 25℃of ambient temperature.
2. Ripple& noise are measured at 20MHz of bandwidth by using a 12”twisted pair-wire terminated with a 0.1uf &47uf parallel capacitor.
3. Tolerance:includes set us tolerance,line regulation and load regulation .
Label
Mechanical Specification
FAQ
How does a LED dimmer switch work?
First and foremost, LEDs are not dimmed based on an increase or decrease of voltage (as is the case with their incandescent counterparts.) ... Instead, what the LED does is it creates a “dimming effect.” There are two ways to do this: pulse-width-modulation (PWM LED) and analog dimming (sans cool-sounding acronym.)