CE ETL FCC ROHS listed 12v 45w power supply for led strip lights
The 12 volt led power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again,can be matched with metal shell, which is easier to install and save than meanwell 45w led driver
Specification
Model
SMT-012-045VM
SMT-024-045VM
SMT-036-045VM
SMT-048-045VM
output
DC Voltage
12V
24V
36V
48V
Voltage Tolerance
±0.5V
Rated current
0~3.75A
0~1.87A
0~1.25A
0~0.93A
Rated power
45W
input
Voltage Range
100-130VAC / 170-265VAC
Frequency Range
47~63HZ
Power Factor (Typ.)
PF≧0.90/110V / PF≧0.90/220V
Efficiency(Typ.)
>88%
>88%
>88%
>88%
AC Current(Typ.)
0.52A@110VAC
0.26A@220VAC0.25A
Leakage current
﹤0.60mA/110VAC / ﹤0.70mA/220VAC
Protection
Short Circuit
Hiccup mode, recovers automatically after fault condition is removed
Over Loading
≦120%
Environment
Working TEMP.
-40~+60℃
Working Humidity
20~90%RH, non-condensing
Storage TEM.,Humidity
-40~+80℃,10~95%RH
TEMP.coefficient
±0.03%/℃(0~50℃)
Vibration
10~500Hz,2G 10min./1 cycle,period for 60min. each along X,Y,Z axes
Safety&EMC
Safety standards
EN61347-1 EN61347-2-13
Withstand voltage
I/P-O/P:3.75KVAC
Isolation resistance
I/P-O/P:100MΩ/500VDC/25℃/70%RH
EMC EMISSION
EN55015,EN61000-3-2,3 (≧50%loading)
EMC IMMUNITY
EN61000-4-2,3,4,5,6,11(Surge 4KV)
Others
Net.Weight
0.55Kg
Size
180*60*34mm(L*W*H)
packing
355*215*215mm/20pcs/CTN
Notes
1. All parameters NOT specially mentioned are measured at 110V / 220VAC input , rated load
and 25℃of ambient temperature.
2. Tolerance: includes set us tolerance, line regulation and load regulation .
3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again
Label
Mechanical Specification
※Input with Live Wire(L) Neutral Wire (N)
※Output LED SEC output Positive(LED+),output negative(LED-).Connected to LED Lamps.
※Signal Dimming (DA1), (DA2) DALI Non polar!Connected to the BUS of the DALI Master.
※ When installing the LED driver and making input and output connections, cross-section area of conductor for input and output terminal block:0.75mm²(cord type: H03VVH2-F or H03VV-F).
※Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
Opreation reference
■Instruction:
1)This driver should be installed by qualified and professional person;
2)Please make sure the transformer is installed with adequate ventilation around it to allow for heat dissipation.
3)Ensure that wiring is correct before test in order to avoid light and power supply damage;
Dimming Operation
※Connect the Dali signal line to the Dali bus of the controller (the Dali Master).
After Dali Master scanning and address assignment, the driver can be successfully dimmed.
Please refer to Diagram 1
※Notice:In the market, some DALI controllers has bus-powered functions .If not,please add an extra power supply.(DALI Power).
※Any incorrect connecting of signal line and output line would damage the master.
FAQ
1. If the connection load less than 55% for the load limitation led driver, what will happen?
Answer: If you take our 1.0V triac dimmable led drivers, the led light will have flick problem.
2. Can we make our company information on the label?
Answer:
--As per the policy of ETL/UL, we can not make changes on the labels at liberty. If we make changes as your requirement , then our company will be punished if the ETL/UL department discover it . Really sorry for that and caused you so much trouble..
--If making changes on the labels are necessary for your company, I suggest you multi-list of our ETL/UL certification , then we can help you design the new label as requested.